OBD I Fehlercodes Pre-FL

[V8Jeeper]

Hier die Liste für "Ausblinkmethode", Anzeige erfolgt über Check Engine Kontrollleuchte im Armaturenbrett als "Morsecode"

Code 11
No Crank Reference Signal at PCM. Condition is no crankshaft reference signal detected during cranking.

Code 12
Battery Disconnect. Condition is direct battery input to PCM disconnected within last 50 key-on cycles.

Code 13
No Chane in MAP from Start to Run. Condition is no difference recognized between MAP reading and barometric pressure reading at start-up.

Code 14
MAP Sensor Voltage too high. Condition is MAP voltage more than acceptable value.

Code 14
MAP sensor Voltage too low. Condition is MAP voltage less than acceptable value.

Code 15
No Vehicle Speed Sensor Signal. Condition is no VSS signal detected with road load conditions.

Code 17
Engine is Cold too Long. Condtion is coolant temperature stays less than normal operating temperature during vehicle operation.

Code 21
O2S Stays at Center. Condition is no rich or lean signal detected from oxygen sensor input.

Code 21
O2S Shorted to Voltage. Condition is oxygen sensor input voltage maintained at more than normal operating range.

Code 22
ECT sensor Voltage too Low. Condition is ECT sensor input less than minimum acceptable voltage.

Code 22
ECT Sensor Voltage too High. Condition is ECT sensor input more than maximum acceptable voltage.

Code 23
Intake Air Temperature sensor Voltage low. Condition is IAT sensor input less than acceptable voltage.

Code 23
IAT more than acceptable voltage

Code 24
Throttle Position Sensor Voltage Low. Condition is TPS input less than minimum acceptable voltage.

Code 24
TPS Voltage High. Condition is TPS more than maximum acceptable voltage.

Code 25
Idle Air Control Motor Circuits. Condition is open or shorted condition detected in one or more IAC motor circuits.

Code 27
Injector Control Circuit (1-8)(1-6). Condition is injector output driver does not respond properly to PCM control signal.

Code 31
EVAP Solenoid Circuit. Condition is open or shorted condition detected in purge solenoid circuit.

Code 32
Exhaust Gas Recirculation Solenoid Circuit. Condition is open or shorted condition detected in EGR solenoid circuit.

Code 32
EGR System Failure. Condition is required change in air/fuel ratio not detected during diagnostic test.

Code 33
A/C Clutch Relay Circuit. Condition is open or shorted condition detected in A/C clutch relay circuit.

Code 34
Speed Control Solenoid Circuits. Condition is open or shorted condition in speed control vacuum or vent solenoid circuits.

Code 34
Speed Control Switch Always Low. Control switch input less than minimum acceptable value.

Code 34
Speed Control Switch Always High. Control switch input more than maximum acceptable value.

Code 41
Generator Field Not Switching Properly. Open or shorted condition detected in alternator field circuit.

Code 42
Auto Shutdown Relay Control Circuit. Open or Shorted condition detected in ASD circuit

Code 42
No ASD Relay Output Voltage at PCM. PCM did not recieve message in ASD relay circuit.

Code 44
Battery Temp Sensor Volts out of Limit. Open or Short condition exists in ECT sensor circuit or a problem is present in PCM battery temp sensor voltage circuit.

Code 46
Charging System Voltage Too High. Battery voltage input more than target charging voltage during engine operation.

Code 47
Charging System Voltage Too Low. Battery voltage input less than target charging voltage during engine operation and no significant change detected in battery voltage during active test of generator field.

Code 51
O2S Stays Below Center (Lean). O2S input indicates Lean during engine operation.

Code 52
O2S Stays Above Center (Rich). O2S input indicates Rich during engine operation.

Code 53
Internal PCM Failure.

Code 53
PCM Failure SPI Communication. PCM failure due to Serial Peripheral Interface (SPI) communication.

Code 54
No Cam SYNC Signal at PCM. Open or shorted condition detected in cam sync signal circuit.

Code 55
Display is Blank. Indicates Completion of trouble code display by the Malfunction Indication Light (MIL).

Code 62
PCM Failure SRI Miles Not Stored. PCM has had an unsuccessful attempt to update Service Reminder Indicator (SRI) miles in PRM EEPROM.

Code 63
PCM Failure EEPROM Write Denied. Unsuccessful attempt to write to an EEPROM location by PCM.


THAT'S ALL OF THEM FOR '93-'95

Getriebecodes gibt es hier
Getriebe-Fehlercodes ZJ / ZG

Klimacodes hier
Klimaanlage-Fehlercodes ZJ / ZG

 

[V8Jeeper]

Um die Threads etwas zu bündeln...

Hier gibt es noch eine Übersezte Version der Codes von Marke63

https://www.jeep-forum.de/threads/blink-codes-liste.144320/