Ray
Member
Threadstarter
- Mitglied seit
- 29.01.2010
- Beiträge
- 3.122
- Danke
- 979
- Standort
- Tharandter Wald, mittendrin
- Fahrzeug
- JLUR 2,2
Der thread ist schon zu, deshalb hier noch meine 2 cent.
Nur mal so als Beispiel der Unterschied Deutsch zu Englisch.
Seite 16, Programmierung von Kundenschlüsseln
HINWEIS:
Bei Wartungs- und Instandsetzungsarbeiten an der funkgesteuertenWegfahrsperre (Sentry Key_) sind alle Fahrzeugschlüssel zum Vertragshändler mitzubringen.
Programmierung von Kundenschlüsseln
Wenden Sie sich an Ihren Vertragshändler, wenn Sie Ersatzschlüssel oder zusätzliche Schlüssel für Ihr Fahrzeug benötigen.
Das liest sich im englischen Manual ab Seite 15 so:
Replacement Keys
NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle.
Once a Sentry Key_ is programmed to a vehicle, it cannot be programmed to any other vehicle.
CAUTION!
Always remove the Sentry Keys_ from the vehicle and lock all doors when leaving the vehicle unattended.
At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.
NOTE: When having the Sentry Key_ Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.
Customer Key Programming
If you have two valid Sentry Keys_, you can program new Sentry Keys_ to the system by performing the following procedure:
1. Cut the additional Sentry Key_ Transponder blank(s) to match the ignition switch lock cylinder key code.
2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.
3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
4. Insert a blank Sentry Key_ into the ignition switch. Turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing.
To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off. The new Sentry Key_ is programmed.
The Remote Keyless Entry (RKE) transmitter will also be programmed during this procedure.
Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key_, contact your authorized dealer for details.
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.
General Information
The Sentry Key_ system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference that may be received, including interference that may cause undesired operation.
Im Deutschen Text vermisse ich auch die Prozedur zum Abschalten des „du bist nicht angeschnallt – Alarms“:
BeltAlert_ kann bei Ihrem Vertragshändler aktiviert oder deaktiviert werden. Chrysler Group LLC empfiehlt, BeltAlert_ nicht zu deaktivieren.
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON
or START position. Chrysler Group LLC does not recommend deactivating BeltAlert_.
1. Turn the ignition switch to the OFF position, and buckle the driver’s seat belt.
2. Turn the ignition key to the ACC/ON position (do not start the engine), and wait for the Seat Belt Reminder
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert_ can be reactivated by repeating this procedure.
NOTE: Although BeltAlert_ has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s seat belt remains unfastened.
DAs meinte ich als ich schrieb "was ernsteres suchen". Im Deutschen wirst du brav zum Freundlichen geschickt.
Gern lasse ich mich korrigieren, wenn ich etwas in der Eile überlesen habe.
Nur mal so als Beispiel der Unterschied Deutsch zu Englisch.
Seite 16, Programmierung von Kundenschlüsseln
HINWEIS:
Bei Wartungs- und Instandsetzungsarbeiten an der funkgesteuertenWegfahrsperre (Sentry Key_) sind alle Fahrzeugschlüssel zum Vertragshändler mitzubringen.
Programmierung von Kundenschlüsseln
Wenden Sie sich an Ihren Vertragshändler, wenn Sie Ersatzschlüssel oder zusätzliche Schlüssel für Ihr Fahrzeug benötigen.
Das liest sich im englischen Manual ab Seite 15 so:
Replacement Keys
NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle.
Once a Sentry Key_ is programmed to a vehicle, it cannot be programmed to any other vehicle.
CAUTION!
Always remove the Sentry Keys_ from the vehicle and lock all doors when leaving the vehicle unattended.
At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.
NOTE: When having the Sentry Key_ Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.
Customer Key Programming
If you have two valid Sentry Keys_, you can program new Sentry Keys_ to the system by performing the following procedure:
1. Cut the additional Sentry Key_ Transponder blank(s) to match the ignition switch lock cylinder key code.
2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.
3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
4. Insert a blank Sentry Key_ into the ignition switch. Turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing.
To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off. The new Sentry Key_ is programmed.
The Remote Keyless Entry (RKE) transmitter will also be programmed during this procedure.
Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key_, contact your authorized dealer for details.
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.
General Information
The Sentry Key_ system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference that may be received, including interference that may cause undesired operation.
Im Deutschen Text vermisse ich auch die Prozedur zum Abschalten des „du bist nicht angeschnallt – Alarms“:
BeltAlert_ kann bei Ihrem Vertragshändler aktiviert oder deaktiviert werden. Chrysler Group LLC empfiehlt, BeltAlert_ nicht zu deaktivieren.
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON
or START position. Chrysler Group LLC does not recommend deactivating BeltAlert_.
1. Turn the ignition switch to the OFF position, and buckle the driver’s seat belt.
2. Turn the ignition key to the ACC/ON position (do not start the engine), and wait for the Seat Belt Reminder
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert_ can be reactivated by repeating this procedure.
NOTE: Although BeltAlert_ has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s seat belt remains unfastened.
DAs meinte ich als ich schrieb "was ernsteres suchen". Im Deutschen wirst du brav zum Freundlichen geschickt.
Gern lasse ich mich korrigieren, wenn ich etwas in der Eile überlesen habe.